How do you check the lid switch on a Maytag washer? (video)
How do you bypass the lid lock on a Maytag washer? (video)
Where is the lid switch on a Maytag top load washer?
Grasp the front of the washer opening with one hand and the back of the cabinet with the other and pull the cabinet forward about 6 inches. You should see the lid switch and have access to it. via
How do you replace a lid switch? (video)
How do I know if my washer lid switch is bad? (video)
How do you lift the lid on a Maytag washer? (video)
Why is my Maytag washer lid not locking?
Common solutions for: Maytag Washer door or lid won't lock
If the door lock is defective, the washer door will not latch properly. The door latch assembly might be defective. Inspect the door latch for damage. If the door latch is damaged, replace it. via
How do I reset my Maytag washer?
How does a washer lid switch work?
The lid switch and lock assembly does two things. First, it detects whether your lid is safely closed so that water can be thrown around inside to wash the clothes. Second, it keeps the lid closed during the wash cycle to prevent messes and accidents. via
Where is the fuse on a Maytag washer?
Maytag washers have a fuse in the lid-switch assembly. Maytag top-loading washers have a fuse in the lid-switch assembly. When you close the lid after adding the laundry and soap, the lid's plastic switch contacts with the assembly underneath. via
Can I bypass the lid switch on my washer?
Most washing machines come equipped with a lid switch. This switch performs the same function, but the lid must be locked in place for the machine to wash. A simple bypass for the first type of lid switch is to simply jam a piece of wood into the switch, causing it to activate the solenoid. via
How much does it cost to replace a lid switch on a washer?
Washer Lid Switch Repair Cost
If the switch on your washing machine lid is broken, the washer probably isn't recognizing that the door is closed and won't start the cycle. Replacing a switch for a washer isn't costly and runs between $90 and $150. via
Where is the washing machine lid switch?
This is the lid switch. It's usually found just under the washer's top, where it can be activated by a small rod on the washer lid, which pushes the switch when the lid is down. If you think about it a little more, you realize that this switch takes a lot of abuse. via
How do you test a washing machine lid switch?
You will need to remove the two-wire harnesses off the lid switch, While you can unmount the lid switch, at this point you only need to test it with a multimeter. Set your multimeter to the lowest ohms of resistance and test your lid switch. If it does not read any continuity, then your lid switch is indeed faulty. via
How do you test a washing machine switch? (video)
How do I bypass the lid switch on a Whirlpool washer?
Follow these steps to perform a Whirlpool washer lid lock bypass: Unplug the washer and move it away from the wall. Remove the top panel by pushing in its retaining tabs or removing its screws. Locate the lid lock switch underneath the top panel. via
How do I take apart a Maytag washer?
Locate the three screws on the top rear edge of the control panel that secure the control panel to the rear of the washer. Remove the three screws with a Phillips screwdriver. Rotate the control console forward and unhook the tabs on the bottom of the control console from the holes in the top of the washer. via
How do you remove the control panel from a Maytag washer? (video)
How do I remove the cover from my Maytag washer? (video)
What do you do when your Maytag washer won't start?
The washer won't start if the lid switch is defective. Disconnect the washing machine from the power supply and open up the housing. Examine the switch to see if it has any burn marks on it or if it's corroded. Order a replacement part from Maytag or an authorized parts dealer if the part appears damaged. via
Can't open my Maytag washer?
If the washer will not unlock at the end of a wash cycle, unplug the washer or disconnect power. Wait approximately 2 minutes for control to reset. Reconnect power to washer (plug in). Run a "Drain and Spin" cycle. via
How do I reset my washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components. via
How do you run a diagnostic test on a Maytag washer? (video)
What is wrong with my Maytag washer?
Some common Maytag front-load washer problems include not agitating or spinning, and not draining or filling with water. Perhaps your washing machine is vibrating during spin cycles or making noises during wash cycles. Look, Maytag is a great brand, but if the washer isn't working that doesn't work for anybody. via
How do you bypass the lid lock on a washing machine? (video)
Why does my washer have no power?
No power issues are typically caused by a tripped circuit breaker, a faulty electrical outlet, a power outage in the home, or in rare cases a unit that requires a repair. via
How dO I know if my thermal fuse is blown?
Touch the left multimeter lead to the left side of the thermal fuse; touch the right multimeter lead to the right side of the fuse. Keep an eye on the multimeter needle; a needle that fails to move indicates a blown thermal fuse. via
Why does my washing machine not turn on?
You should check the outlet to make sure it's working. Then, check if a fuse is blown or a circuit breaker thrown. If those both work, see if the Delay Start button or Control Lock feature has been activated. Sometimes it's as simple as opening and closing the door to reset the washer. via