When the boards having the heads are being discarded, a simple way to remove them is to cut through the screws at the joint between the board. You can use a reciprocating saw (often called by a brandname, Sawzall) via
How do you remove old screws from a deck? (video)
How do you remove deck boards with stripped screws?
What is the easiest way to remove deck boards? (video)
How do you remove an embedded screw from wood? (video)
How do you remove a screw that spins but won't come out?
Sometimes using a Torx or flat heat driver bit can get traction and torque to get the screw moving. If that fails, its best to use a screw extractor. Screw extractors have sharp, rough metal threaded tips. These tip burrow into the softer screw head metal, and allow you to apply torque and loosen the screw. via
How do you unscrew a screw that won't budge?
Hammer the impact driver
Hold the body of the impact driver to prevent it from turning. Then hit the end with a serious blow. If the screw still won't budge and the surrounding surfaces can tolerate some heat, aim a lighter flame directly onto the screw head. Then douse it with cold water before trying it again. via
Why are my deck screws rusting?
Rust occurs as a reaction of iron with oxygen, causing an orange-colored film to spread on screws, eventually having the potential for the screw to disintegrate entirely. When building your deck, you want to make sure that it can last a long time without having to worry about corrosion. via
How do I remove painted deck screws? (video)
How do you remove CAMO deck screws?
If a CAMO Marksman tool is stuck on the deck board, it is typically because the CAMO fastener is not fully driven into the joist. Don't try to pull and remove the tool because you may break it. Rather, remove the screw by reversing the drill and backing it out or continue to force the screw into the deck board. via
What can I replace decking with?
The rest in the list, while an option, aren't terribly popular.
Can you flip old deck boards?
Flipping Deck Boards - Be Careful About Wood Grain
They are treated lumber." You bet you can flip them. There's no harm in doing so. While you're at it, be sure to clean off any debris from the top of the support joists and check for rot at those locations. via
Can I just replace deck boards?
If your existing deck is old, shabby and a maintenance nightmare, you don't have to tear it all down and start over. Chances are that the structural parts are still in good shape. If so, you can simply remodel it with new decking, rails and stairs, and save tons of money over the cost of a complete rebuild. via
Can you unscrew wood screws?
Put the screw extractor into the pilot hole on the screw and gently tap it in place with a hammer until it is secure. You can now use a pair of pliers to grip the screw extractor and turn it to the left. The teeth of the screw extractor dig into the pilot hole, which will allow you to continue unscrewing it. via
Why won't screws go all the way in?
If the drill applies too little force, the screw will stop spinning before the screw is all the way into the wood. The higher the number, the more force the drill tries to apply to the screw. So, if your screw won't go all the way into the wood, turn the clutch setting to a higher number. via
Why won't my screws come out?
If the screw is being especially stubborn, try using a hammer. With one hand, hold your screwdriver in place and slowly try to turn it while hitting the back of the screwdriver with a hammer. This is the same premise that an impact driver works on. More often than not, I can get almost any screw free using this trick. via
How do you unscrew a really tight screw? (video)
How do you remove a lost thread screw?
Does wd40 loosen screws?
If the bolt is stuck in place because of rust, you can use a bolt loosening spray such as WD-40 Penetrant Spray. This penetrating oil provides deep lubrication to loosen the nut or screw. This will help the formula to penetrate the fitting and loosen the bolt so that it can be removed easily. via
How do I keep my deck screws from rusting?
Moisture can cause metal screws to become rusted. The easiest way to prevent rust on screws is to shield them completely from moisture, be it through selective placement or protective coatings and sealants. Purchasing specially formulated, rust resistant or rustproof screws is usually helpful, as well. via
Are deck screws waterproof?
Stainless steel decking screws are another great option when it comes to outdoors screws and nails, as well as stainless steel screws. Both have properties that make them weather resistant, and are especially hardy against rain. via
Are black drywall screws rust proof?
Although the coating does help prevent rusting, it doesn't stop rusting altogether, which is why black drywall screws are recommended only for indoor projects, due to their tendency to sometimes rust. via
Can you paint over screws?
You can paint almost anything with spray paint, but it's particularly useful for painting small fasteners, screws, hooks, and pieces of hardware that would be difficult to paint any other way. Spray paint the fasteners. To spray paint hardware — hinges, latches, braces, and brackets — use a bent piece of wire. via
How do you hide screws on a wooden deck? (video)
How do deck screws work? (video)
How do you install decking without screws? (video)
How many years will a wood deck last?
A deck made of untreated wood can last anywhere from 10 to 30 years. Decks made of treated wood and composite materials can last as long as 50 years. Many composite decks come with a 20-year warranty – and often a lifetime guarantee. via
What can I cover my old deck with?
Interlocking deck tiles are a low-cost way to transform your deck into a safer, more attractive space while helping to protect the actual deck from wear and tear. Installing outdoor tile over a wood deck can help to protect you from splinters, while offering the deck protection from sun and wear and tear. via
How often should you replace your deck?
The International Association of Certified Home Inspectors estimates decks made from wood planks will last about 15 years, while structural wood will give you 10 to 30 years. Composite decking will last anywhere from eight to 25 years. via